Posted on

growing skunk from seed

Dummies has always stood for taking on complex concepts and making them easy to understand. Dummies helps everyone be more knowledgeable and confident in applying what they know. Whether it’s to pass that big test, qualify for that big promotion or even master that cooking technique; people who rely on dummies, rely on it to learn the critical skills and relevant information necessary for success.

Learning Made Easy

Copyright © 2021 & Trademark by John Wiley & Sons, Inc. All rights reserved.

Raising a seedling, however, requires some patience, gentle hands, and a smidgen of luck. Thankfully pot seeds are remarkably vigorous because they are what’s called endosperm seeds, which means they have almost pre-formed cotyledon leaves before you even add water. Below is a brief guide on the techniques we have found yield the most success when starting seeds and raising your seedling to a healthy plant ready for transplanting.

Seedlings require a medium amount of light in which it has enough to grow but not too much light that it gets burned. Leaving your seedling in direct sunlight will cause the leaves to curl, while too little light will cause the seedling to stretch. If growing outside, seedlings want to see a direct light source to stop them stretching. If inside, a sunny windowsill with more than half a day of sunlight works wonders. Otherwise, 18 in away from a growing light works excellently. Your seedling should not stretch more than 6 in at most. We’ll cover lighting in more depth in a later blog.

Starting From Seed

We like to use seedling pellets that are made of a mix of compressed peat moss and coco husk. To expand, soak it in water for 10 minutes. Once your seedling pellet has absorbed enough water and has expanded to its maximum size, drain off any excess water. The growing medium should be like a damp sponge that would not leave streaks on the table. Dig a small hole about 1/4 in deep for your seed. Use a spoon to lift the seed out of its bath. If it has popped out a taproot be careful not to damage it. Gently place the seed into the hole and lightly cover it with dirt from the pellet. Now that you have started the germination process, your seedling will come above ground within two weeks. The older the seed, the longer it takes for it to germinate.

Our favorite thing about starting from a seed, rather than a clone, is that you get to see the full life cycle and enjoy a plant that is unique, just like you. An entirely new genetic makeup will enter the world for the first time, and if you’re lucky, something remarkable might be born.

To accelerate germination, you are going to want to soak your seed in a small container with lukewarm water and place it in a dark and warm place for 12-24 hours, but no longer. By drenching the seed, it absorbs the water thoroughly, activating the germination process. Doing this also helps to loosen the shell as it becomes a little softer making it easier for the embryo to crack it open. When your seed sinks to the bottom it is ready to be planted, and sometimes the seed will pop out a small taproot. A seed can still be planted though if it does not sink.

But if the seed you found looks decent, you might as well germinate it and see what sprouts.

Check out Johanna’s full video series on how to grow weed on Leafly’s YouTube .

One drawback of clones is they need to be taken during the vegetative stage of a plant—flower is too late—so if you have a small setup with only one light, it can be hard to keep clones alive while flowering other plants, because the two need different amounts of light.

Is the seed viable?

A seed has germinated once the seed splits and a single sprout appears. The sprout is the taproot, which will become the main stem of the plant, and seeing it is a sign of successful germination.

For the typical homegrower, it may be easier to obtain cannabis seeds rather than clones. Growing from seed can produce a stronger plant with more solid genetics.

For a seed to be viable, it must be mature enough to have a completely formed genetic blueprint, and it must be strong enough to germinate and pop through its hard casing and sprout its crucial taproot.

A couple big drawbacks, though: Autoflower strains are known for being less potent. Also, because they are small in stature, they usually don’t produce big yields.