Posted on

autoflower germination method

Place one sheet of damp kitchen towel on a flat surface. Space your seeds a few centimetres apart before placing the second piece of kitchen towel over the top. You need to ensure both pieces are damp, not wet. Once again, when the white root tips reach 2–3mm, move the seeds (carefully) to soil pots. Use the same guidance found above for planting techniques.

Maintaining the ideal temperature (between 22–25°C/71–77°F) and moisture for germination is tricky. Leaving seeds out in the open environment or on a windowsill is far from ideal; a DIY climate-controlled cupboard would do a much better service. A warming mat is perfect for maintaining a constant temperature, but it doesn’t tackle the issue of moisture.

Three fundamental principles will trigger that first small taproot to appear: warmth, moisture, and darkness. With the promise of moisture, a single root will take shape before slowly developing into the cannabis plant we know and love. In the right conditions, seeds will begin to develop within 12–36 hours of moisture being introduced to them.

GLASS OF WATER APPROACH

Arguably one of the least effective methods, but it is still viable. Incredibly simple to facilitate, beginner growers may opt to germinate their seeds in a glass of water. Half-fill a glass or bowl with water that is approximately 22°C (71°F).

The Royal Queen Seeds Feminized Starter Kit contains:

Start by filling pots with a premium-quality soil that has been soaked in water. Many growers also choose to lace the water with a root stimulator. Make a hole roughly 10–15mm deep. This will be your seed’s new home. Remove the seeds from their packet and place them into the pre-dug holes. Loosely cover the seeds, but be careful not to compress the soil above the seed too much. The root will struggle to penetrate solid soil, slowing plant growth. Lightly spray the top of where you placed the seed so that your growing medium stays moist.

Contents:

Just take your autoflower cannabis seed and put it in a wet growing medium 2 to 3 times as deep as the width of the seed. That little plant will shoot its tap root down into the ground and with those seed leaves will try to find the light.

If you are in a colder environment you need to get a heating pad that can heat up your growing medium and if you are in a hot environment get some fans or install an air conditioning unit.

Growing medium preparation

Before putting your seed inside a growing medium you should fully wet that medium by flushing and only after it has dried up a bit you can put the seed in it. Almost any growing medium will be suitable for autoflower seed germination and you just need to check if the PH level is not too high or too low.

Autoflowering cannabis seeds are just like any regular ones and the process of germination is the same, in fact, the only differences are in the way you treat you seedling when it has sprouted. Some growers say that autoflower seeds can be germinated in colder temperatures but I have not tested this hypothesis myself and have not seen side by side tests that show temperature differences and autoflower seed germination rates.

The second stress that those seeds should not encounter is temperature fluctuations as they can also damage the germination rate, in the ideal conditions temperature should stay the same all the way till the autoflower seed has sprouted and won’t dip in the night time or rise in the daytime.

You should keep your seeds in an airtight container in a fridge set at 6-8°C with a relative humidity of between 20-30%, if you can’t set your fridge to the temperatures mentioned, just keeping them in the fridge will increase the chances of germination.

Place the seeds in the glass and leave it in a dark place, let the seeds soak for up to 32 hours.

Slightly Open The Seed

As the title says, grab a glass cup and fill it half with water.

So how to germinate a marijuana seed in a germination chamber? To start germinating, make a small hole (1-2 cm) in moisten medium, cover without applying pressure, turn on the heat mat and spray the humidity dome, it should take a couple of days to see the seedling coming out.

Just grab a pencil, or even with your fingers, make a little hole (1-2cm deep), and place the seed in it, the medium must be moist but not soaking, then cover with soil without applying pressure.